OBD2 and Dash Plug solution for Ford F150 Full Virtual Dashboard now available in FORZA 614
Some vehicles need an introduction. The Ford F-150 does not. In 2021 alone Ford sold 726,004 F-Series trucks in the United States - the 45th year in a row as America’s best-selling truck and the 40th as its best-selling vehicle. The current, fourteenth generation (P702) arrived for the 2021 model year, and with it came a fully digital 12.4-inch instrument cluster.
That many trucks means that many clusters and sooner or later, some of them land on a workshop bench. Ours came from eBay USA: a Ford F150 instrument cluster labelled P702 2022 MY, part number NL3T-10849-CCB, LX MPH version.
Here is what we found.
FORD F150 Digital Instrument Cluster 24C64 Programming with FORZA 614
What the F-150 digital cluster looks like
This is one of the cleanest digital dashboards we have had on the bench. Two large blue rings: tachometer on the left and speedometer on the right, with four small gauges across the top for coolant temp, oil pressure, transmission temp and fuel. The centre menu (MyView, Trip/Fuel, Truck Info, Towing) is simple and very readable, exactly what you want in a work truck.
Behind the screen sits a heavy cast housing with FoMoCo markings, and the board is sealed to it with generous amounts of blue thermal paste. This gauge cluster was built to get rid of heat.
Inside the cluster: two computers on one board
The main PCB is marked VPML3F-14A608-AF / PWB24989 - the cluster was designed by Visteon. What makes it interesting is the split architecture: one microcontroller handles the vehicle side (CAN-bus, mileage, warning logic), while a separate graphics module with its own processor, RAM, flash and power management draws everything you see on the display.


- Main microcontroller: Spansion S6J334DJTE ARM-based MCU that handles CAN-bus communication, odometer logic and the core cluster functions.
- EEPROM: 24C64 stores the mileage, engine hours and configuration. It sits right next to the main MCU.
- Companion memory: Spansion chip at U402 located beside the S6J334.
- Graphics processor: NXP i.MX 8 family, marked SIMX8668035FFAB (mask set 1N94W) a full applications processor responsible for rendering the gauges and menus.
- Power management IC: NXP SC33PF8100 (PF8100 series) supplies the i.MX 8 module.
- Graphics module memory: Micron chips marked D9WQM, NQ451 and two marked RW337 RAM and storage for the graphics processor.


Date codes on the graphics module point to late 2021, which matches the 2022 model year label on the housing.
LS124M5LZ04 FORD F150 12.4" Display
The display in the Ford F-150 digital cluster is the LS124M5LZ04, a 12.4-inch colour panel, made in Vietnam. It is mounted in its own metal frame and connects to the main board through a wide flat cable and a smaller secondary connector.
Because the panel is a separate assembly, it can be unplugged from the PCB without touching the electronics. If you are searching by display part number, LS124M5LZ04 is the one printed on the label at the back of the panel.

NL3T-10849-CCB and the Super Duty twins
Our unit carries the part number NL3T-10849-CCB. The same style of cluster is not limited to the F-150 the Super Duty F-250 and F-350 use twin clusters that look the same. If you work on Ford trucks, you will meet this dashboard more than once.

What goes wrong with the F-150 digital cluster
We will be straight with you: we have not repaired dozens of these yet. But owners of 2021 and 2022 trucks describe the same symptoms again and again:
- The screen goes black while driving, or stays black after start-up, while the rest of the truck works normally.
- The whole display freezes - it keeps showing the last speed and does not switch off with the ignition. After a battery disconnect it comes back black, with only the PRNDM indicator lit.
- Glitches after over-the-air software updates, including the speed unit jumping between MPH and km/h.
- Flickering and odd behaviour at start-up caused by a weak 12V battery - always check it before condemning the cluster.
In some reports the cluster, the radio and the steering wheel buttons freeze together. That matters for diagnosis: when several modules fail at once, the cluster may not be the culprit at all.
The dealer’s answer: a new cluster
Owners describe two typical outcomes at the dealer. Either the fault codes are cleared and the truck goes home until it happens again, or the whole instrument cluster is replaced with a new one - sometimes after a long wait for the part.
A used cluster costs a fraction of a new one. The problem is that it arrives with someone else’s mileage and engine hours. That is exactly where an independent workshop can step in.
POWER UP Ford Clusters with FORZA 614 - testing the cluster outside the truck
This cluster will not light up from power and ground alone. It needs CAN-bus frames to wake up. FORZA 614 sends them for you: connect the cluster on the bench, click POWER UP, and the dash starts for a few seconds with full graphics - long enough to check the display and confirm that the cluster communicates over CAN-bus.
No separate CAN-bus generator is needed. And it answers the key diagnostic question: if the cluster wakes up and talks on the bench, the fault is more likely in the truck’s network than in the cluster itself.
To be clear, FORZA 614 will not repair a dead cluster. It lets you test it outside the vehicle before you decide what to replace.
FORZA 614 software programming options for Ford F-150 speedometer
- Mileage - read and write, reset to 0 or set to any value.
- Engine hours - read and write, reset to 0 or set to any value.
- Cluster identification - reads the production numbers and software version of the cluster.
ℹ️ The way mileage and engine hours are coded in the 24C64 is very complex, and there are several different storage versions. Editing a raw EEPROM dump by hand is a risky way to work on this cluster. FORZA 614 handles the coding for you, diagnostically, through the cluster connector.
Two jobs come up most often. The first is a cluster replacement: you fit a used unit and restore the truck’s original mileage and engine hours, so the dash shows the true values again. The second is reset to 0 - useful for companies selling used parts, and for cases where a dealer will only adapt a replacement cluster that shows zero.
Ford F-150 Instrument Cluster Pinout
In the truck you connect through the OBD2 socket. On the bench you need two cables: F1, the main adapter that connects FORZA 614 to the cable set, and F2.
The Ford F-150 dashboard pinout is included in the FORZA 614 app, together with board photos. The app is free to download and install – you can look up the pinout before you subscribe to anything.

Seven hundred thousand trucks a year, and one dealer answer
The numbers work in your favour. The F-Series sells in huge volumes, the digital cluster has known problems, and the official fix is an expensive new part.
A workshop that can test a cluster on the bench and set the correct mileage on a used replacement has a real service to sell.
Bench work also means the truck does not have to be in your yard. Clusters can be mailed in from anywhere - from other garages, from importers and exporters, from used parts sellers who want their stock tested and reset before it goes on the shelf.
One subscription, no extra licences
FORZA 614 runs on a simple subscription. There are no separate licences for individual models and no token fees. The Ford F-150 program is included, and so is every cluster we add next. More programs for new Ford models are on the way.
You might also like
- VW Amarok digital cluster S6J334 + 24C64
- Ford Focus 2025 instrument cluster RX7T-14F094-TCA
- Ford Expedition R7F701441 Instrument Cluster Programming
- Ford F150 R7F701441 Speedometer Programming
FAQ
Do I need a CAN-bus generator to start this cluster on the bench?
No. The POWER UP button in FORZA 614 sends the CAN-bus frames and wakes the cluster for a few seconds with full graphics.
Does a Ford instrument cluster need to be programmed after a swap?
A used cluster keeps the mileage and engine hours of the truck it came from. With FORZA 614 you can set both to the correct values for the vehicle it is going into.
Where is the mileage stored in the Ford F-150 digital cluster?
In the 24C64 EEPROM on the main board, next to the Spansion S6J334 microcontroller. Engine hours are stored there too.
Can FORZA 614 fix a black screen on an F-150 cluster?
No. It helps you test the cluster outside the truck and program a replacement, but it does not repair hardware faults.
Does this cover the F-250 and F-350?
The Super Duty F-250 and F-350 use twin clusters that look the same as the F-150 unit.