OBD2 and Dash Plug solution for Ford F250 Speedometer now available in FORZA 614
Hey everyone!
Today on the workbench we have a big American dash: the Ford F-250 Super Duty instrument cluster from a 2024 model-year truck, part number RC3T-10849-DF. Like many units we’ve added to FORZA 614, this one came from eBay USA. We bought it for one reason: to get it fully supported in the app, so workshops can start it on the bench, test it and program it without the rest of the truck.
As soon as it powered up, you can tell it’s a Super Duty. There are four small gauges along the top for oil pressure, coolant temperature, fuel and a turbo boost gauge reading 0-40 PSI. Two big gauges with ice-blue backlighting sit either side of a colour LCD, and the PRNDM gear strip runs underneath. The factory label on the housing reads “P708 2024 MY - L1 Cluster MPH Turbo” with a production date of 16 April 2024, Made in Mexico.
Ford F250 Dashboard Programming on the bench with FORZA 614
This article covers what’s inside this Ford F250 dashboard, what to watch for during troubleshooting and what FORZA 614 can do with it on your bench.

Inside the Ford F-250 Super Duty instrument cluster
Under the lens there’s one main PCB, marked VPML3F-14A608-CE (P702 L1 / PWB24817). You will find there a single ARM-based Traveo microcontroller with external HyperBus flash and RAM for the graphics, plus a 24C64 serial EEPROM for configuration data. The front of the board carries the LEDs, the display and the two main gauge motors. The four small gauge motors are mounted on the back.


- Main microcontroller: S6J32HELTN. A Traveo ARM MCU that runs the gauges, the display graphics and CAN-bus communication with the rest of the vehicle.
- Serial EEPROM: 24C64. Stores the cluster’s configuration and adaptation data.
- HyperFlash memory: 3× S26KL512S. External flash for the firmware and graphics resources shown on the LCD.
- HyperRAM: S27KL0642. Working memory for the display rendering.
- Main gauge stepper motors: Sonceboz 6403R200. These drive the speedometer and tachometer needles and are mounted on the front of the PCB.
- Small gauge stepper motors: Sonceboz 6405R407. Four white units on the back of the board drive the oil pressure, coolant, fuel and turbo needles.

The two different Sonceboz stepper families on one board are worth noting if you stock motors for repairs. The big gauges and the small top gauges don’t share the same part.

LAM042G044C Center Display in FORD F250
The central colour TFT is marked LAM042G044C. This is the 4.2-inch screen used in the mid-trim Super Duty clusters, between the basic small display and the 8-inch “productivity” cluster that some owners upgrade to. The display is a separate module held to the board with screws and connected through an FFC ribbon. You can unplug it and test it on its own without touching the rest of the instrument cluster. On the bench, FORZA 614 brings the cluster up with full graphics on this LCD, so you can tell straight away whether a blank screen is a display fault or a communication problem.

Same cluster in the Ford F-150 and F-350
This isn’t only an F-250 part. The same instrument cluster design is used in the Ford F-150 and the Ford F-350 Super Duty. So when an F-150 or F-350 cluster lands on your bench, expect the same layout we described above. The S6J32HELTN microcontroller, the 24C64 EEPROM, the HyperFlash memory and the LAM042G044C display are all on the board. The bench procedure is the same too: CAN-bus wake-up through FORZA 614, display and gauge testing, a part number and software readout, and the same pinout in the app.
For workshops this is good news. One set of skills, one bench setup and one subscription cover three of Ford’s best-selling trucks. That’s a lot of clusters coming through the door, especially from US imports and used-parts sellers.
💡 Matching hardware doesn’t mean every unit can be swapped straight into another truck. Faceplates, gauge sets (gas vs. diesel, with or without a turbo gauge), MPH/km/h versions and configuration differ between versions. Always compare the part number and software version of both units before you install a donor cluster.
Common faults and troubleshooting
- Dead or blank display while the needles still move. This usually points to the LCD module, its ribbon connection, or the graphics side of the board rather than the whole unit. Wake the cluster on the bench before you condemn the screen.
- Cluster dropping off the network. When the instrument cluster stops talking on CAN-bus, the other modules in the truck typically log U0155 – Lost Communication with Instrument Panel Cluster (IPC) Control Module. Checking the cluster on the bench separates a faulty unit from a wiring or connector problem in the vehicle.
- Stuck, jumping or lazy gauge needles. Watch all six gauges sweep on the bench. With two different stepper motor types on this board, check each needle on its own.
Full instrument cluster wake-up on the bench
The 2024 Ford Super Duty instrument cluster doesn’t fully start on 12V alone. It needs CAN-bus frames from the vehicle before the gauges and display come alive. FORZA 614 provides that wake-up, so you don’t need the truck or a separate CAN-bus generator on your bench. You get a fully running dash with complete graphics on the display, and you can test CAN-bus communication, the LCD, the backlighting and every gauge before and after the repair.
For shops that specialise in instrument cluster repair, this is the main time saver: every unit that comes in can be powered up, checked and signed off in minutes.
FORZA 614 software programming options for Ford F-250 dashboard
Diagnostically, FORZA 614 reads the cluster’s part number and software version, so you can confirm which unit is on the bench and whether it matches the donor or customer vehicle.
FORZA 614 also offers mileage and engine hours reset for this cluster. Shops selling used Super Duty clusters ask for this a lot, because a unit pulled from a high-mileage F-250 or F-350 has to go out clean. Vehicle importers who change out units on trucks brought in from the US need it for the same reason.
ℹ️ 24C64 access: The 24C64 EEPROM in this cluster cannot be read or written diagnostically, either through the dash connector or through OBD2. To back up the original data or make a complete 1:1 clone onto a donor cluster, you’ll need a serial EEPROM programmer connected directly to the 24C64 chip.
Ford F-250 Dashboard Pinout
The Ford F-250 Super Duty cluster uses a 16-pin (2×8) connector on the back of the housing. The full Ford F250 24C64 Instrument Cluster Pinout is available inside the FORZA 614 app. You don’t have to work out power, ground and CAN lines from wiring diagrams; connect it and go.

Why workshops take on Ford Super Duty instrument cluster repair
A new cluster from the dealer is expensive, and on a truck like this the owner usually wants the original unit fixed and back in quickly. With bench wake-up, display testing and the pinout ready in the software, you need less equipment on the bench and fewer hours per job. You can accept mail-in Ford Super Duty instrument cluster repair work without having the truck in the shop.
We’re also working on this all the time. Our goal is to make FORZA 614 the most user-friendly device for instrument cluster repairs and programming. Every cluster we buy, test and add, like this F-250, takes another manual step out of your process.
One Simple Subscription
FORZA 614 runs on a flat-rate subscription. You don’t pay per-job tokens or hidden credit costs, and new clusters and features keep arriving through regular software updates. Support for units like this 2024 Ford F-250 is included in your plan as soon as it’s released.
You might also like
- Ford Ranger 93C86 Speedoemter programming
- Ford Expedition R7F701441 Instrument Cluster Programming
- Ford F150 Virtual Insturment Cluster 24C64+S6J334
- VW Amarok digital cluster S6J334 + 24C64
FAQ
Does the Ford F-250 instrument cluster need CAN-bus to start on the bench?
Yes. The 2024 Ford F-250 Super Duty cluster needs CAN-bus frames to fully wake up. FORZA 614 provides them, so no separate CAN-bus generator is needed.
What EEPROM is used in the 2024 Ford F-250 instrument cluster?
The 2024 Ford F-250 Super Duty instrument cluster (RC3T-10849-DF) uses a 24C64 serial EEPROM alongside an S6J32HELTN microcontroller.
Can the 24C64 be read through OBD2?
No. The 24C64 in this cluster cannot be read or written diagnostically. A full backup or 1:1 clone requires a serial programmer connected directly to the chip.
Are there extra fees per cluster?
No. FORZA 614 is a flat-rate subscription with no token fees.