FORZA 614 is the tool that can reset the odometer value in the Bentley Bentayga speedometer with the MB9DF125E MCU.
Hi everyone!
We’re continuing the series of clusters we’re bringing into FORZA 614. Yesterday it was the Audi A5 8W6, and today we’re back with the Bentley Bentayga instrument cluster, part number 36A920870. It’s also the first Bentley ever added to FORZA 614.
A Bentayga cluster on the bench makes most technicians a little careful. It’s a rare part, an expensive part, and if something goes wrong, you can’t just grab another one from the scrapyard down the road. That’s exactly why we wanted to show you this one in detail before you take on the job.
The cluster comes from the first-generation Bentley Bentayga, the version with real needles in chrome-ringed dials. Under the leather-and-chrome image there’s a surprise for anyone who read yesterday’s article: the electronics are the same Bosch platform as the Audi A5 8W6 Bosch cluster. Same processors, same architecture. Bentley gave it a different face, more needles and its own display, and that’s what this article focuses on.
Bentley Bentayga Instrument Cluster Odometer Reset to 0
What sets the Bentayga dash apart
From the front, there’s nothing Audi about it. The Bentayga cluster uses four physical needles: a large speedometer and tachometer, plus two smaller dials set inside them for coolant temperature and fuel. The speedometer carries a dual scale, mph on the outside up to 200, km/h on the inner ring up to 320. The tachometer reads up to 7,000 rpm. Our unit, part number 36A920870 came from a mile-based market.
That four-dial layout is why the board carries more stepper motors than the two-needle Audi. Each dial has its own motor, and on this cluster they’re a different type:
- Gauge stepper motors: 6405R472 (marking 16067E1.2) - four units, one per needle. Not the same part as in the two-needle Audi, but that’s no reason to worry: these motors are easy to find on the market for a few to a dozen or so euros each. If a needle starts sticking, jumping or losing its zero position, replacing the motor is a quick, cheap board-level fix, not a reason to replace the whole cluster.

The Bosch electronics under the Bentley face
The logic board follows the same two-processor layout as its Audi sibling: one chip for the graphics, a second for everything the car sees on CAN. The date codes on our unit (weeks 01 and 04 of 2016) match the start of Bentayga production.
- Main microcontroller: Fujitsu MB9DF125E (ARM, Traveo family), Bosch marking F04L000480 - needles, telltales and vehicle communication.
- Graphics processor: Fujitsu MB86R11F (ARM, BGA) - drives the center screen.
- SDRAM: 2× Winbond W631GG6KB15K - DDR3 memory for the graphics side.
- NOR flash: Spansion GL128S100DHB02 (Bosch F04L000482).
- NAND flash: Spansion S99ML01G10041 (Bosch F04L000481).
- Telltale LED drivers: TI 6C598 shift registers.
The whole board sits under a perforated metal shield, with the grey multi-pin connector coming through at the side. That connector is all FORZA 614 needs.




LAM0703556B Center Display
Here’s the second big difference from the Audi. The Bentayga uses a LAM0703556B 7-inch colour TFT, Bosch number 8 928 554 127-01, instead of the Sharp panel in the A5 cluster. It’s mounted in its own frame with a flex connection to the main board and carries the trip data, warnings and driver assistance graphics.
If you’re quoting a display repair on a Bentayga, don’t assume an Audi panel will fit just because the board is the same. Check the part number on the back of the screen first.

Where Bentayga clusters cause trouble
Since the electronics are shared, so are the weak points - plus one that comes with the extra dials:
- Display faults that start under the BGA. A dark, flickering or broken picture is often traced back to the solder joints of the MB86R11F graphics processor rather than to the LAM0703556B panel. On a Bentley, where a new display costs serious money, it pays to check the BGA before ordering parts.
- Total shutdown. When the whole cluster goes dead - needles, lights and screen together - the problem is usually on the main board itself.
- Sticking or jumping needles. With four dials, there are four stepper motors that can wear out. A needle that sticks, jumps or doesn’t return to zero usually means a worn 6405R472 motor. Replacements are widely available and inexpensive, so it’s a repair you can quote low and still do profitably.
- Bench messages. Without the rest of the car, the cluster shows warnings for systems it can’t find. Don’t treat those as faults.
FORZA 614 software programming options for the Bentley Bentayga dashboard
On a car like this, the customer has one clear expectation: after a cluster swap or repair, the mileage on the dash must match the car. That’s the job FORZA 614 does here.
- Odometer correction in both directions - set a higher or lower value, so a used or repaired cluster shows the vehicle’s real mileage.
- Through the dash plug - no soldering and no opening the housing a second time. The connection diagram is in the app.
- Up to 10 minutes for a typical job.
One thing to know before you start: the Bentayga cluster won’t wake up on power alone. It needs CAN-bus frames from the car or a CAN simulator. FORZA 614 doesn’t need it awake - the programming runs while the cluster stays dark, and you see the result the next time it starts with CAN present.
ℹScope for this cluster: FORZA 614 changes the odometer value only. Reading or writing the full memory contents is not supported, so there’s no data backup or 1:1 cloning onto a donor for this cluster.
Bentley Bentayga Dashboard Pinout
The Bentley Bentayga instrument cluster pinout - power, ground and CAN lines - is shown in the FORZA 614 connection diagram for this cluster, and the pinout graphic is available below.

Why a Bentayga job is worth your bench time
Not many workshops are willing to take in a Bentley cluster. That works in your favour. The owner has fewer places to go, a new cluster from Bentley is expensive, and a job that takes up to 10 minutes through the connector can be quoted with confidence. Board-level repairs - the display, the power side or a worn stepper motor - add even more value, especially for mail-in customers who can’t find a specialist locally.
FAQ
Is the Bentley Bentayga cluster the same as the Audi A5 Bosch cluster?
The electronics are the same Bosch platform, with Fujitsu MB9DF125E and MB86R11F processors. The Bentayga has its own front design with four needles, different stepper motors (6405R472) and a different display (LAM0703556B).
What display does the Bentley Bentayga instrument cluster use?
A 7-inch colour TFT, part number LAM0703556B, Bosch number 8 928 554 127-01.
Can a faulty Bentayga needle be fixed without replacing the cluster?
Yes. Sticking or jumping needles are usually caused by a worn 6405R472 stepper motor, which is widely available for a dozen euros.
Do I need a CAN simulator to program the Bentayga cluster?
Not for programming. FORZA 614 programs the odometer while the cluster stays dark. A CAN source is only needed to start the cluster and see the result.
Which Bentley Bentayga cluster part number is supported?
Our unit was part number 36A920870. Clusters with similar part numbers should be supported as well. If a new version turns up and we get one into our office, we’ll add it to FORZA 614 too.