Another new cluster in FORZA 614 and we’re not slowing down
A great option for every workshop repairing and coding instrument clusters. FORZA 614 keeps delivering top solutions for automotive electronics, one new cluster after the next.
This one arrived almost brand new. The label says it was built on 14 December 2024, so it’s about as fresh as clusters get on our desk. It’s the new fully digital dash from the 2025 Ford Bronco Sport refresh - the CX430 compact SUV, not the full-size Bronco. If you’ve had one of these in for a cluster swap, mileage correction or diagnosis, you already know there isn’t much published about it yet. Here’s what’s inside, what we expect to go wrong with it over time, and how FORZA 614 reads and programs mileage on it - through OBD2 or on the bench.
Ford Bronco Sport 24C64 Dashbaord Odometer Reset by OBD2 or Dash Plug
What’s inside the Ford Bronco Sport 2025+ cluster
The housing tells you straight away this isn’t an ordinary dashboard. The whole rear cover is die-cast aluminium, with cooling fins over the graphics section and a perforated speaker grille cast into the corner. The PCB is VPNUBF-14A608-FB (PWB27396, revision SX2, PCB date code 2432). The design is split into two parts. An Infineon TRAVEO T2G microcontroller handles vehicle logic, CAN communication and the odometer. A separate NXP i.MX 8 application processor with its own DRAM and eMMC renders the full graphical display. Mileage lives in a SOIC8 external I²C EEPROM 24C64 next to the main MCU.


- Main microcontroller: CYT3BB7CEBQ1AE (Infineon/Cypress TRAVEO T2G, 176-pin TEQFP) - Arm Cortex-M7 automotive body-control MCU with up to 4 MB code flash; runs cluster logic, CAN networks and odometer handling.
- EEPROM: 24C64 (8-pin SOIC, next to the MCU) - stores the mileage.
- MCU external flash: Spansion KL128S series, 128 Mbit - external memory serving the TRAVEO MCU.
- Graphics processor: NXP i.MX 8DualX, MIMX8DX5AVLFZAC - BGA application processor that renders the screen; sits under a metal lid with thermal pads onto the aluminium housing.
- eMMC storage: Samsung KLM8G1GEUF - 8 GB eMMC holding the graphics system and assets.
- DRAM: Micron (FBGA code D8FDP) - working memory for the i.MX 8.
- Additional Micron memory: FBGA code RW303 - part of the graphics subsystem.
- Automotive Ethernet PHY: NXP TJA1101B - a 100BASE-T1 transceiver, next to a dedicated two-pin connector on the board. You don’t see this in most clusters, but it’s becoming a regular feature in the newest Ford dashboards.


LS123M5LZ05 / NU5T-14F872-BA Display 12.3" FORD
The screen is a 12.3-inch colour LCD module marked LS123M5LZ05, carrying the Ford part number NU5T-14F872-BA, made in Vietnam. It connects to the main board with a wide flat ribbon, and a second small flex goes to the PCB on the display side. The display sits in its own carrier, so it comes out without disturbing the main PCB. At this stage we haven’t seen these screens fail and we can’t comment on replacement availability – the units are simply too new.

Cluster label for reference: S1PT-10849-BG, CX430 2025 MY, SX2, made in Mexico.

Fault patterns.. what we expect, not what we’ve seen
Here we have to be honest: so far we haven’t seen a single failed unit of this cluster. Most of these cars are still under warranty.
That said, this cluster runs hot. On the bench, the rear casing warms up noticeably within minutes. The design relies entirely on passive cooling: the i.MX 8 graphics processor, the eMMC and the DRAM are all BGA packages pressed against the aluminium cover through thermal pads, and the finned section of the casing is the only heat path. Our theory is this:
- Repeated heat cycling under the BGA graphics processor and memory is the most likely long-term killer. Expect black screens, frozen graphics or a cluster stuck in reboot loops while the TRAVEO side keeps talking on CAN.
- Thermal pads drying out or shifting after years in a hot dashboard would speed this up.
- Because the odometer sits in the 24C64 on the MCU side, a dead graphics section doesn’t take the mileage with it. That matters when you’re swapping to a donor.
We’ll update this section once real failures start coming in.
Bench power up Ford instrument cluster
These clusters don’t wake up from power alone. They need specific CAN frames before they boot properly. FORZA 614 takes care of that on the bench, so you don’t need a separate CAN generator. Once running, the screen shows “Blind spot system fault”, PRNDL, ABS, BRAKE and a row of amber warning lamps - all normal with the rest of the car missing.
One thing that catches people out: on the bench, the cluster doesn’t display the mileage. You won’t see the odometer on the screen. That’s not a fault - just click Read in FORZA 614 and you get the value straight from the cluster.
FORZA 614 software programming options for the Ford Bronco Sport 2025+ dashboard
What the current release does on the CYT3BB + 24C64 cluster:
- Instrument Cluster POWER UP - you can test the cluster on the bench just with one click using FORZA 614.
- Read mileage - via OBD2 in the car or through the dash connector on the bench.
- Write mileage to any value - to correct a replacement cluster to the vehicle’s real mileage.
- Reset mileage to 0 - many dealer workshops will only adapt a replacement cluster that shows zero, so this gives a good used cluster a second life instead of buying a new one.
No soldering, no opening the housing and no touching the BGA side of the board.
ℹ️ Full EEPROM read/write not available yet: a full diagnostic read and write of the 24C64 isn’t available yet - we’re working on it. On this cluster, what comes out diagnostically may not be a raw 1:1 image of the chip.
ℹ️ Ford OBD2 detail worth knowing: on Fords, the cluster doesn’t sit on the standard OBD2 CAN pair (pins 6 and 14). Ford routes its secondary CAN network to pins 3 (CAN+) and 11 (CAN−) of the diagnostic socket. Generic CAN-only adapters wired for pins 6/14 won’t see the cluster at all - FORZA 614 handles the correct pins for you.
Ford Bronco Sport 2025+ Dashboard Pinout
On the bench, connect through the cluster’s main connector using cables F1 + F2. F1 is the main FORZA 614 adapter, F2 plugs into it. The pinout graphic marks four pins on the connector: power, ground and the CAN pair. The same pinout is available inside the FORZA 614 app.

Why a brand-new Ford cluster is worth having in your menu now
Every 2025 Bronco Sport on the road will eventually need a cluster swap - after a crash, a water leak or a graphics failure like the one we expect above. A new cluster from Ford is expensive. Adapting a used one to the real mileage, or zeroing it for the dealer, is a quick bench job with the right software. Workshops that support these clusters early get those jobs while everyone else is still asking around. Mail-in repairs work well too: the customer ships the cluster, you read it, correct it and send it back the same day.
This isn’t the only new-generation Ford in FORZA 614 - see our Ford Focus 2025 RX7T-14F094-TCA cluster article. More programs for the newest Ford models are coming soon.
One subscription, no per-model fees
FORZA 614 runs on one flat subscription - currently €99 per month. No tokens, no per-vehicle licences, and every new cluster we add, including the upcoming Ford models, is part of it. For comparison, some software packages for the newest Fords sell for more than €2,000, and some for over €3,000 - per package. With FORZA 614 the low entry cost keeps your workshop flexible, and the subscription funds the development that keeps new models coming every week.
FAQ
What EEPROM does the Ford Bronco Sport 2025+ cluster use?
The 2025+ Bronco Sport instrument cluster stores mileage in a 24C64 EEPROM, next to an Infineon CYT3BB7CEBQ1AE TRAVEO T2G microcontroller.
Can I read the mileage through OBD2?
Yes. FORZA 614 reads and writes mileage on this cluster through OBD2 in the car, or through the dash connector on the bench with cables F1 + F2.
Can FORZA 614 make a full EEPROM backup of this cluster?
Not yet. Mileage read, write and reset are supported today, and full diagnostic EEPROM read/write for the 24C64 is in development.
Why doesn’t the cluster show mileage on the bench?
Without the rest of the vehicle, the screen doesn’t display the odometer. FORZA 614 reads the value directly from the cluster.
Do I need a CAN-bus generator to start this cluster on the bench?
No. The cluster needs specific CAN frames to boot, and FORZA 614 sends them.